Browse Website

 

 

We have discovered the article about Installing A Bathtub below on the web and decided it made good sense to write about it with you here.

Mounting a bathtub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bath tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either situation, the project is within a home handyman's skills, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the job and also are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed job, it is much better to think about using one prior to you start. Chances are you may need a professional plumber to make tube links.
This post will certainly assist you mount a brand-new tub in your shower room if you have actually currently gotten a new tub and don't need to alter the arrangement of your previous supply of water pipes.
Your tools and material checklist ought to make up the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Getting ready for the Setup

First of all, the supporting structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final placement.

 

 

Removing Old Taps

If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome as a result of the restricted access that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a fabric all set for the staying water that will originate from the pipes. Once the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

 

 

Installing the Bath tub

Using both wooden boards under its feet, put the bathtub in the needed position. The wood boards are helpful in uniformly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bath tub until the spirit level checks out degree.
To install taps, fit the bottom of the outermost adaptable tap connector to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Activate the water and inspect all joints and also new pipework for leakages and tighten them if needed. Load the bathtub and additionally examine the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, take care of the bathroom paneling as described in the maker's user's manual. Tiling and also sealing around the bath tub should wait up until the tub has actually been used at least once as this will certainly resolve it right into its final position.

 

 

Fitting New Taps

If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place between the tap as well as the sink. Protect the tap in place with the producer supplied backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type should be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Bathtub

In the area where the bathroom satisfies the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, creating the water to permeate the wall in between the bathroom and also the tiling, causing problems with dampness and also possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can fracture fairly very early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof adhesive and also grout.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

I stumbled upon that content about How to Install a Bathtub Yourself while looking around the web. Loved our piece? Please share it. Let other people discover it. I thank you for reading our article about A Step-by-Step Guide to Installing a Bathtub.

Schedule Your Service